Bavaria Cruiser 46 Style, Hana (2020)

Bavaria Cruiser 46 Style, Hana is moored at Marina Kornati Biograd, Croatia.

 

It was produced in 2020, and with a simple and elegant layout, it has three cabins ideal for accommodating seven people with three toilets, so it has perfect dimensions for short and long journeys on the Adriatic Sea.

 

Onboard, the level of comfort exceeds all expectations.

Technical information

Base Dalmacija Zadar, Marina Kornati Biograd
Model: Bavaria Cruiser 46 Style
Year built: 2020
Cabins: 3
Berths: 7
Berths (+): 7 (6+1)
Heads: 3
Length (m): 14.27
Beam: 4.35 m
Draught: 2.1 m
Length at waterline: 13.60
Engine: 1 x 75 HP
Water capacity: 360 l
Fuel capacity: 210 l
Service type: Bareboat
Deposit (€): 2200
Hints & Tips

Electric panel

Control panel + Main switch

Particular functions are marked next to every switch on the panel and explained by our skippers during the check in.
The main power switch is located next to navigation table.
By turning off service switch all the electricity on board shuts down. The possibility is primarily used in an emergency situation, for example in case of fire.

Fuses and shore indicator

LEDS near every switch indicate whether the particular device is on or not.
Make sure to check the shore power connection by checking the 220 V (green light on the panel). Please connect to the shore power cable whenever you have the opportunity.

Windlass fuse

Is located behind the seat in salon near captain's table

Engine switch

Engine switch is located under the stairs

Inverter

Please make sure that all devices connected to the inverter should be used only as long as necessary, for example, until mobile phone battery is charged, after which it should immediatelly be disconnected. Keep in mind that the inverter consumes the electricity even if there is no device connected to it, so in order to preserve enegry, please switch it off after every use.

Valves

Emergency fuel cutoff valve

It is located in starboard stern cabin
It is to be used in case of an emergency (fire).

Gas valve in the galley

It is located in galley above fridge. The valve is open when the lever is in horizontal position and closed when it is in vertical position.
1
2

Gas valve in cockpit

Turn to open or close. When the stove is not in use, please close the valve. When changing the bottle, lay it on the side, hold the valve and slowly turn the bottle until it is tight.

Sanitation

Toilet

By pulling and pushing the lever you can pump the seawater in and out of the toilet bowl.
If the small lever of the pump is in the left position, the water goes in and out at the same time. If it's in the right position, the water goes only out.
Make sure both seacocks are open when using the toilet.
After the use please close both of them.

CAUTION!!!!
DO NOT throw paper tissues, napkins or other garbage in the toilet bowl because it may clog the drain pipes.
To avoid unpleasant situation and extra expenses, please dispose the toilet paper and other garbage into a plastic bag.

Seacocks

Seacocks are in the toilettes under the sink

Water supply switching lever

It is located in the toilette in the port stern cabin.
CAUTION!!!!
When one water tank is empty, immediately close all the running taps in order to avoid the pump to take air into the system. Turn the lever to switch the water supply to the other tank and open the tank.
The water should start flowing after couple of seconds.

Engine and engine control panel

Engine compartment

All engines are regularly maintained by our mechanics.
Nevertheless, to be sure it is working properly, check the oil and water levels regularly, as well as inspecting the engine visually.
The procedure of controlling the engine will be elaborated by our skippers during the check-in.

Engine control panel:engine start/stop,gear lever,fuel level indicator,hour meter

Starting the engine:
1. Switch on the electric contact (button on the upper left side of the EVC panel).
2. Hold the start switch with light pressure (upper right on the EVC panel) for about 10 seconds (preheat)
3. Push the button fully to start the engine
4. The gear lever must be in neutral position,otherwise you will not be able to start the engine

Stopping the engine:
1. Push the stop button (lower right on the PVC panel)
2. Switch off the electric contact
Please return the gear lever to the neutral position before shutting down the engine.
Cruising speed is at about 2500 RPM. Faster than that puts great tension on the engine and the clutch and could result in damage.

 

Bow thruster

To engage the bow thruster, push both ON buttons. Maximum usage is for 10 seconds.

Navigation instruments

Exterior instruments

During the check – in, our skippers will explain the basic functions of all instruments. For more in-depth information you can consult user manual which is located in one of the cupboards in the galley
1
2

Charterplotter & Autopilot

GPS is located in front of both rudders and the user manual is in the same folder with other manuals.

Autopilot is located next to the right rudder.

Anchor

Anchor and chain compartment + Electric windlass

During the maneuver please attach the compartment hatch to the fence using the provided rope with the hook. Please make sure the anchor doesn't hit the bow during anchoring procedure.
While lowering the anchor, engine should be turned on and in neutral running mode approximately 1500 rpms untill you release wanted lenght.After that put the gear lever to neutral and engage it slowly back to check that the anchor is holding well.

CAUTION!!!
Just before you start lifting the anchor, engage the forward gear for 2-3 seconds (with minimum gas, just to get a slight push forward in the direction of the anchor). That way you will prevent the windlass to pull the whole boat, which can seriously damage it.
To avoid injury, wear gloves and shoes while operating the windlass.
The chain is marked every 10 m with a red mark.

Deck and dinghy

Cockpit shower

The boat is equipped with cockpit shower.
Please pull out the hose with care to avoid damage
After the use check whether the tap is closed.
1
2

Dinghy and Outboard engine

To avoid damage to impeller, please always start the outboard engine in water.
When dinghy is not in use, please return it to its position on the deck; if you tow it behind the boat, there is a chance of losing it along the way, and that case is not covered by any insurance.
Also, DO NOT tow the dinghy while the outboard engine is still mounted on it.
After each use please return the outboard engine to its place on board.

Bilge

Bilge pump

Automatic bilge pump is located in sallon under the floor.
If there is water in the bilge, the floating switch starts the pump.

Safety equipment

1
2

Lifejackets & Liferaft

All lifejackets will be in the salon during check in reafy for your inspection, so please during the check out leave them in the same place so we can check them. Liferaft is located in cockpit in one of the locker.

Hints & Tips

In case of any damage that can be repaired on spot by yourself or with a help from a third person, please immediately contact our base in order to arrange eventual expense coverage in needed.
When returning to our base, please enter between the piers in reverse gear because the space between them is rather narrow

Our website uses cookies for better user experience

By continuing to browse our website you agree to our use of cookies which helps us provide you with a good user experience on our website. We use Google Analytics for our own analytical purposes and it installs cookies for this purpose (delete GA cookies). More about cookies.

I AGREE